P0111MA 1AA3

P011xx Sensitive high immunity SCRs up to 0.8 A Features A ■ IT(RMS) up to 0.8 A ■ VDRM/VRRM 400 and 600 V ■ IGT from 0.5 to 25 µA G K Description A Thanks to highly sensitive triggering levels, the P011xx SCR series is suitable for all applications where available gate current is limited, such as ground fault circuit interruptors, pilot circuits in solid state relays, standby mode power supplies, smoke and alarm detectors. KA K G G A SOT-223 (P011xxN) TO-92 (P011xxA) Available in through-hole or surface-mount packages, the voltage capability of this series has been upgraded since its introduction and is now available up to 600 V. Table 1. Device summary Voltage Sensitivity Order code Package 400 V 600 V Min. Max. P0111DA 1AA3 X 4 µA 25 µA TO-92 P0111DA 5AL3 X 4 µA 25 µA TO-92 P0111DN 5AA4 X 4 µA 25 µA SOT-223 P0111MA 1AA3 X 4 µA 25 µA TO-92 P0111MA2AL3(1) X 4 µA 25 µA TO-92 P0111MN 5AA4 X 4 µA 25 µA SOT-223 P0115DA 1AA3 X 15 µA 50 µA TO-92 P0115DA 5AL3 X 15 µA 50 µA TO-92 P0118DA 1AA3 X 0.5 µA 5 µA TO-92 P0118DA 5AL3 X 0.5 µA 5 µA TO-92 P0118DN 5AA4 X 0.5 µA 5 µA SOT-223 P0118MA 2AL3 X 0.5 µA 5 µA TO-92 P0118MA 5AL3 X 0.5 µA 5 µA TO-92 1. This order code has no space. January 2009 Rev 1 1/9 www.st.com 9 Characteristics P011xx 1 Characteristics Table 2. Absolute ratings (limiting values) Symbol IT(RMS) Parameter IT(AV) Average on-state current (180° conduction angle) ITSM Non repetitive surge peak on-state current I²t TO-92 Tl = 55 °C SOT-223 Tamb = 70 °C TO-92 Tl = 55 °C SOT-223 Tamb = 70 °C RMS on-state current (180° conduction angle) tp = 8.3 ms tp = 10 ms Unit 0.8 A 0.5 A 8 Tj = 25 °C A 7 I²t Value for fusing tp = 10 ms Tj = 25 °C 0.24 A2 S dI/dt Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns F = 60 Hz Tj = 125 °C 50 A/µs IGM Peak gate current tp = 20 µs Tj = 125 °C 1 A Tj = 125 °C 0.1 W - 40 to + 150 - 40 to + 125 °C PG(AV) Tstg Tj Table 3. Average gate power dissipation Storage junction temperature range Operating junction temperature range Electrical characteristics (Tj = 25 °C, unless otherwise specified) Symbol IGT Test conditions VD = 12 V P0111 P0115 P0118 Min. 4 15 0.5 Max. 25 50 5 Unit µA RL = 140 Ω VGT 0.8 V Min. 0.1 V Min. 8 V VD = VDRM RL = 3.3 kΩ RGK = 1 kΩ VRG IRG = 10 µA IH IT = 50 mA RGK = 1 kΩ Max. 5 mA IL IG = 1 mA RGK = 1 kΩ Max. 6 mA dV/dt VD = 67 % VDRM VTM ITM = 1.6 A Vt0 Rd RGK = 1 kΩ Tj = 125 °C Max. VGD IDRM IRRM 2/9 Value Tj = 125 °C Min. Tj = 25 °C Max. 1.95 V Threshold voltage Tj = 125 °C Max. 0.95 V Dynamic resistance Tj = 125 °C Max. 600 mΩ tp = 380 µs VDRM = VRRM = 400 V RGK = 1 kΩ VDRM = VRRM = 600 V RGK = 1 kΩ VDRM = VRRM RGK = 1 kΩ 80 75 75 V/µs 1 Tj = 25 °C Tj = 125 °C Max. 10 100 µA P011xx Characteristics Table 4. Thermal resistance Symbol Parameter Rth(j-a) Junction to case (DC) Rth(j-t) Junction to tab (DC) Rth(j-a) Junction to ambient (DC) Maximum Unit TO-92 80 °C/W SOT-223 30 °C/W TO-92 150 SOT-223 60 °C/W S(1) = 5 cm2 1. S = Copper surface under tab. Figure 1. Maximum average power Figure 2. dissipation versus average on-state current P(W) Average and DC on-state current versus lead temperature IT(AV)(A) 1.0 1.1 0.9 D.C. (SOT-223) 1.0 α = 180° 0.9 0.8 0.8 0.7 D.C. (TO-92) 0.7 0.6 0.6 0.5 α = 180° (SOT-223) 0.5 0.4 0.4 0.3 0.3 360° 0.2 α = 180° (TO-92) 0.2 0.1 IT(AV)(A) 0.0 0.1 Figure 3. 0.2 0.1 α 0.0 0.3 0.4 0.5 Tlead(°C) 0.0 0 0.6 Average and DC on-state current versus ambient temperature 25 Figure 4. 50 75 100 125 Relative variation of thermal impedance junction to ambient versus pulse duration K=[Zth(j-a)/Rth(j-a)] IT(AV)(A) 1.00 1.2 1.1 Device mounted on FR4 with recommended pad layout D.C. (SOT-223) 1.0 0.9 0.8 TO-92 0.7 D.C. (TO-92) 0.6 0.10 α = 180° (SOT-223) 0.5 SOT-223 0.4 0.3 α = 180° (TO-92) 0.2 0.1 tp(s) Tamb(°C) 0.0 0 25 50 75 0.01 100 125 1E-2 1E-1 1E+0 1E+1 1E+2 5E+2 3/9 Characteristics Figure 5. P011xx Relative variation of gate trigger, Figure 6. holding and latching current versus junction temperature Relative variation of holding current versus gate-cathode resistance (typical values) IH[RGK] / IH[RGK=1kΩ] IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25°C] 20 6 Tj = 25°C 18 typical values 5 16 14 4 12 3 10 IGT 8 2 6 1 4 IH & IL RGK = 1kΩ Tj(°C) 2 RGK(kΩ) 0 -40 -20 Figure 7. 0 20 40 60 80 100 120 140 0 1E-2 1E-1 Relative variation of dV/dt immunity Figure 8. versus gate-cathode resistance (typical values). 1E+0 1E+1 Relative variation of dV/dt immunity versus gate-cathode capacitance (typical values) dV/dt[CGK] / dV/dt[RGK=1kΩ] dV/dt[RGK] / dV/dt[RGK=1kΩ] 10 10.0 VD = 0.67 x VDRM Tj = 125°C RGK = 1kΩ Tj = 125°C VD = 0.67 x VDRM 8 6 1.0 4 2 RGK(kΩ) 0.1 CGK(nF) 0 0 0.2 Figure 9. 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 1 2 3 4 5 6 7 Surge peak on-state current versus Figure 10. Non-repetitive surge peak on-state number of cycles current and corresponding value of I²t ITSM(A), I2t (A2s) ITSM(A) 100.0 8 Tj initial = 25°C 7 ITSM tp=10ms 6 One cycle sinusoidal pulse with width tp < 10ms 10.0 5 Non repetitive Tj initial=25°C 4 3 Repetitive Tamb=25°C 1.0 2 I2t 1 Number of cycles 0 1 4/9 tp(ms) 10 100 0.1 1000 0.01 0.10 1.00 10.00 P011xx Ordering information scheme Figure 11. On-state characteristics (maximum Figure 12. Thermal resistance junction to values) ambient versus copper surface under tab ITM(A) Rth(j-a)(°C/W) 1E+1 130 120 110 100 90 80 70 60 50 40 30 20 10 0 Tj max.: Vt0=0.95V Rd=600mΩ 1E+0 Tj=max Tj=25°C 1E-1 VTM(V) 1E-2 0.5 2 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Epoxy printed circuit board FR4, copper thickness: 35 µm S(cm²) 0.0 4.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Ordering information scheme Figure 13. Ordering information scheme P 01 1x x x Blank xAxx Sensitive SCR series Current 01 up to 0.8 A Sensitivity 11 = 4 to 25 µA 15 = 15 to 50 µA 18 = 0.5 to 5 µA Voltage D = 400 V M = 600 V Package A = TO-92 N = SOT-223 Packing mode 1AA3 = Bulk 2AL3 = Ammopack 5AL3 = Tape and reel 13 inch 5AA4 = Tape and reel 7 inch 5/9 Package information 3 P011xx Package information ● Epoxy meets UL94, V0 In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 5. TO-92 dimensions dimensions Ref Millimeters Min Typ Max Inches Min Typ Max A a B A 1.35 B C 4.70 C F 6/9 D E 0.053 0.185 2.54 0.100 D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 P011xx Package information Table 6. SOT-223 dimensions Dimensions Ref. V A A1 c Typ. Inches Max. Min. Typ. 1.80 A1 0.02 Max. 0.071 0.001 B 0.60 0.70 0.80 0.024 0.027 0.031 B1 B1 2.90 3.00 3.10 0.114 0.118 0.122 c 0.24 0.26 0.32 0.009 0.010 0.013 4 D 6.30 6.50 6.70 0.248 0.256 0.264 D E 1 Min. A B e1 H Millimeters 2 3 e e 2.3 0.090 e1 4.6 0.181 E 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 V 10° max Figure 14. Footprint (dimensions in mm) 3.25 1.32 5.16 7.80 1.32 2.30 0.95 7/9 Ordering information 4 P011xx Ordering information Table 7. Ordering information Order code Marking Package Weight Base qty Packing mode P0111DA 1AA3 P0111 DA TO-92 0.2 g 2500 BAG P0111DA 5AL3 P0111 DA TO-92 0.2 g 2000 Tape and reel 13 inch P0111DN 5AA4 P1D SOT-223 0.11 g 1000 Tape and reel 7 inch P0111MA 1AA3 P0111 MA TO-92 0.2 g 2500 Bag P0111 MA TO-92 0.2 g 2000 Ammopack P0111MN 5AA4 P1M SOT-223 0.11 g 1000 Tape and reel 7 inch P0115DA 1AA3 P0115 DA TO-92 0.2 g 2500 Bag P0115DA 5AL3 P0115 DA TO-92 0.2 g 2000 Tape and reel 13 inch P0118DA 1AA3 P0118 DA TO-92 0.2 g 2500 Bag P0118DA 5AL3 P0118 DA TO-92 0.2 g 2000 Tape and reel 13 inch P0118DN 5AA4 P8D SOT-223 0.11 g 1000 Tape and reel 7 inch P0118MA 2AL3 P0118 MA TO-92 0.2 g 2000 Ammopack P0118MA 5AL3 P0118 MA TO-92 0.2 g 2000 Tape and reel 13 inch P0111MA2AL3 (1) 1. This order code has no space. 5 Revision history Table 8. 8/9 Document revision history Date Revision 26-Jan-2009 1 Description of changes First issue. P011xx Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 9/9